DPAS04HP0 (phased out)
DevicePort Advanced Mode Powered COM Ethernet enabled 4-port RS-232 Port Replicator
- Expands 4 RS-232 serial ports over Ethernet or WiFi.
- Provides RS-232 serial ports with +5VDC power output via COM 9th pin.
- Communication speeds up to 115.2Kbps.
- Real-Time data transmitting (Real COM) without complicated IP setup.
- COM Port Auto-Detect and Port-Mapping supports Plug-N-Play.
- Built-in with SUNIX DPL2000Q High-Performance Ethernet-UART controller.
- Built-in dual 10/100 Ethernet ports for Ethernet cascading capability.
- Compatible with existing software and AP.
- To make wiring simple, fast, and more space efficient.
- Easy maintenance with Fixed COM number and Hot-Swap.
- SUNIX DevicePort proprietary Ethernet I/O Redirection Technology.
- Supports Daisy Chain Topology and up to 255 COM ports expansion.
- Data buffer prevents any unforeseen data loss during a connection failure.
- Flexible port configuration with DevicePort on/off-line smart COM deployment.(Note 2)
- 15KV ESD protection for all serial signals meets IEC-61000-4-2 standard.
- Low power consumption design of 2.5W for meeting Green Environmental movement.
- Certified by CE, FCC, VCCI, BSMI, RoHS and Microsoft WHQL approval.
Introduction
DPAS04HP0 allows users to expand four RS-232 Powered COM ports over Ethernet connection, and it works on any windows based desktop, thin client, laptop, All-in-one, and tablet PC computers. With SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology, DevicePort® creates physical COM ports that support real time data communication, Smart COM on/off-line deployment, and Ethernet-COM port hot-plug capability; user can expand RS-232 COM port easily without complex software configuration. SUNIX DevicePort® improves solution deployment efficiency to achieve greater reliability in commercial and industrial automation applications.
Features
Specifications
Serial Communication
| Interface | RS-232 | Baud rate | 50bps ~115.2Kbps |
| Controller | SUNIX DPL2000Q | Stop bit | 1, 1.5, 2 |
| BUS | Ethernet | Parity | even, odd, none, mark, space |
| No. of Port | 2-port | Flow Control | Xon/Xoff (software) |
| FIFO | 1Kbyte Hardware / per port | Connector | DB9 Male |
| Signal | DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI | ||
| Protection |
±15KV ESD IEC-61000-4-2 Air Discharge ±8KV ESD IEC61000-4-2 Contact Discharge ±4KV ESD IEC61000-4-2 Level2 Line-to-Line |
||
Ethernet Communication
| Number of Ports | 4-port, Ethernet Switch Port |
| Speed | 10/100 Mbps, auto MDI/MDIX |
| Connector | RJ45 |
| Magnetic Isolation Protection | 1.0K Built-in |
Power Requirements
| Input Power Voltage | +5VDC |
| Output Powered COM Capacity |
+5VDC / Maximum 750mA / each port Note: Total power output capacity will be limited by connected power source. |
| Over Current Protection | 1.1A PTC fuse for each power signal |
| Power Consumption | 2.5W @ 5VDC (board only without power output to serial device) |
| Connector | DC-Jack |
Driver Support
| Windows Client | XP (X86) / 7 / 8 / 8.1 / 10 (X86/X64) |
| Windows Server | 2003 / 2008 / 2012R2 (X64) |
Regulatory Approvals
| Hardware | CE, FCC, VCCI, BSMI |
| Software |
Microsoft WHQL Windows • Microsoft Client: XP (X86) / 7 / 8 / 8.1 (X86/X64) • Microsoft Server: 2003/2008/2012R2 (X64) |
Environment
| Operation Temperature | 0 to 45°C (32 to 113°F) |
| Operation Humidity | 5 to 95% RH (non-condensing) |
| Storage Temperature | -20 to 85°C (-4 to 185°F) |
Physical Characteristics
| Housing | ABS, PC, Metal |
| Weight | 283g |
| Dimensions | 190x119.58x27(mm), 7.5x4.8x1.0(inch) |
Note:
1.DevicePort Advance Mode limits specific Ethernet port connection, and it does not works on router operation.
2.DevicePort on/off-line smart COM deployment.
- Auto connection and mapping with MAC address bound.
- Keeps physical COM port in system when DevicePort under off-line mode.
- Serial signal staging until DevicePort recovery back to on-line mode.
Accessories
Including Accessories
Power Adapter 5VDC@1A (US / EU)
- Partner No.: 1AAC-B205V10U10000 (US Type)
- Partner No.: 1AAC-B205V10E10000 (EU Type)
- US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
- (ψ5.5 *ψ2.0 / 120cm)
- Partner No.: 1WDC-Y1120G4100000
- 1 pcs
Support
Download Manual
| Manual | DevicePort Powered COM RS-232 Advanced Mode Manual |
|
| Version | V10 英文版 | |
| Update | 2016-05-25 09:51:13 | |
| Size | 4.3MB |
Download Datasheet
| Datasheet | DPAS04HP0 Datasheet |
|
Download Guide
| Guide | Advanced-Powered |
|
Download Driver
| Driver | DevicePortAdvanced V3.0.8.0 | |
| Version | Ver 3.0.8.0 | |
| Update | 2020-01-21 14:34:24 | |
| Size | 7.3MB | |
| OS |
Windows 10 32/64 bit
Windows 8.1 32/64 bit
Windows 8.0 32/64 bit
Windows 7 SP1 32/64 bit
Windows Server 2012 R2 64-bit
Windows Server 2012 64Bit
Windows Server 2008 R2 SP1 64bit
|
| Driver | Linux TTY Driver Ver 1.0.15.0 | |
| Version | Ver 1.0.15.0 | |
| Update | 2019-09-16 15:21:59 | |
| Size | 2MB | |
| OS |
CentOS7.0
Ubuntu 11.10
Ubuntu 12.04
Ubuntu 13.10
Ubuntu 14.04
Ubuntu 14.10
Ubuntu 15.04
Ubuntu 15.10
Ubuntu 16.04
|
DPAS04HP0 (phased out)
DevicePort Advanced Mode Powered COM Ethernet enabled 4-port RS-232 Port Replicator
- Expands 4 RS-232 serial ports over Ethernet or WiFi.
- Provides RS-232 serial ports with +5VDC power output via COM 9th pin.
- Communication speeds up to 115.2Kbps.
- Real-Time data transmitting (Real COM) without complicated IP setup.
- COM Port Auto-Detect and Port-Mapping supports Plug-N-Play.
- Built-in with SUNIX DPL2000Q High-Performance Ethernet-UART controller.
- Built-in dual 10/100 Ethernet ports for Ethernet cascading capability.
- Compatible with existing software and AP.
- To make wiring simple, fast, and more space efficient.
- Easy maintenance with Fixed COM number and Hot-Swap.
- SUNIX DevicePort proprietary Ethernet I/O Redirection Technology.
- Supports Daisy Chain Topology and up to 255 COM ports expansion.
- Data buffer prevents any unforeseen data loss during a connection failure.
- Flexible port configuration with DevicePort on/off-line smart COM deployment.(Note 2)
- 15KV ESD protection for all serial signals meets IEC-61000-4-2 standard.
- Low power consumption design of 2.5W for meeting Green Environmental movement.
- Certified by CE, FCC, VCCI, BSMI, RoHS and Microsoft WHQL approval.
Introduction
DPAS04HP0 allows users to expand four RS-232 Powered COM ports over Ethernet connection, and it works on any windows based desktop, thin client, laptop, All-in-one, and tablet PC computers. With SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology, DevicePort® creates physical COM ports that support real time data communication, Smart COM on/off-line deployment, and Ethernet-COM port hot-plug capability; user can expand RS-232 COM port easily without complex software configuration. SUNIX DevicePort® improves solution deployment efficiency to achieve greater reliability in commercial and industrial automation applications.
Features
Specifications
Serial Communication
| Interface | RS-232 | Baud rate | 50bps ~115.2Kbps |
| Controller | SUNIX DPL2000Q | Stop bit | 1, 1.5, 2 |
| BUS | Ethernet | Parity | even, odd, none, mark, space |
| No. of Port | 2-port | Flow Control | Xon/Xoff (software) |
| FIFO | 1Kbyte Hardware / per port | Connector | DB9 Male |
| Signal | DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI | ||
| Protection |
±15KV ESD IEC-61000-4-2 Air Discharge ±8KV ESD IEC61000-4-2 Contact Discharge ±4KV ESD IEC61000-4-2 Level2 Line-to-Line |
||
Ethernet Communication
| Number of Ports | 4-port, Ethernet Switch Port |
| Speed | 10/100 Mbps, auto MDI/MDIX |
| Connector | RJ45 |
| Magnetic Isolation Protection | 1.0K Built-in |
Power Requirements
| Input Power Voltage | +5VDC |
| Output Powered COM Capacity |
+5VDC / Maximum 750mA / each port Note: Total power output capacity will be limited by connected power source. |
| Over Current Protection | 1.1A PTC fuse for each power signal |
| Power Consumption | 2.5W @ 5VDC (board only without power output to serial device) |
| Connector | DC-Jack |
Driver Support
| Windows Client | XP (X86) / 7 / 8 / 8.1 / 10 (X86/X64) |
| Windows Server | 2003 / 2008 / 2012R2 (X64) |
Regulatory Approvals
| Hardware | CE, FCC, VCCI, BSMI |
| Software |
Microsoft WHQL Windows • Microsoft Client: XP (X86) / 7 / 8 / 8.1 (X86/X64) • Microsoft Server: 2003/2008/2012R2 (X64) |
Environment
| Operation Temperature | 0 to 45°C (32 to 113°F) |
| Operation Humidity | 5 to 95% RH (non-condensing) |
| Storage Temperature | -20 to 85°C (-4 to 185°F) |
Physical Characteristics
| Housing | ABS, PC, Metal |
| Weight | 283g |
| Dimensions | 190x119.58x27(mm), 7.5x4.8x1.0(inch) |
Note:
1.DevicePort Advance Mode limits specific Ethernet port connection, and it does not works on router operation.
2.DevicePort on/off-line smart COM deployment.
- Auto connection and mapping with MAC address bound.
- Keeps physical COM port in system when DevicePort under off-line mode.
- Serial signal staging until DevicePort recovery back to on-line mode.
Accessories
Including Accessories
Power Adapter 5VDC@1A (US / EU)
- Partner No.: 1AAC-B205V10U10000 (US Type)
- Partner No.: 1AAC-B205V10E10000 (EU Type)
- US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
- (ψ5.5 *ψ2.0 / 120cm)
- Partner No.: 1WDC-Y1120G4100000
- 1 pcs
Support
Download Manual
| Manual | DevicePort Powered COM RS-232 Advanced Mode Manual |
|
| Version | V10 英文版 | |
| Update | 2016-05-25 09:51:13 | |
| Size | 4.3MB |
Download Datasheet
| Datasheet | DPAS04HP0 Datasheet |
|
Download Guide
| Guide | Advanced-Powered |
|
Download Driver
| Driver | DevicePortAdvanced V3.0.8.0 | |
| Version | Ver 3.0.8.0 | |
| Update | 2020-01-21 14:34:24 | |
| Size | 7.3MB | |
| OS |
Windows 10 32/64 bit
Windows 8.1 32/64 bit
Windows 8.0 32/64 bit
Windows 7 SP1 32/64 bit
Windows Server 2012 R2 64-bit
Windows Server 2012 64Bit
Windows Server 2008 R2 SP1 64bit
|
| Driver | Linux TTY Driver Ver 1.0.15.0 | |
| Version | Ver 1.0.15.0 | |
| Update | 2019-09-16 15:21:59 | |
| Size | 2MB | |
| OS |
CentOS7.0
Ubuntu 11.10
Ubuntu 12.04
Ubuntu 13.10
Ubuntu 14.04
Ubuntu 14.10
Ubuntu 15.04
Ubuntu 15.10
Ubuntu 16.04
|
DPAS04HP0 (phased out)
DevicePort Advanced Mode Powered COM Ethernet enabled 4-port RS-232 Port Replicator
- Expands 4 RS-232 serial ports over Ethernet or WiFi.
- Provides RS-232 serial ports with +5VDC power output via COM 9th pin.
- Communication speeds up to 115.2Kbps.
- Real-Time data transmitting (Real COM) without complicated IP setup.
- COM Port Auto-Detect and Port-Mapping supports Plug-N-Play.
- Built-in with SUNIX DPL2000Q High-Performance Ethernet-UART controller.
- Built-in dual 10/100 Ethernet ports for Ethernet cascading capability.
- Compatible with existing software and AP.
- To make wiring simple, fast, and more space efficient.
- Easy maintenance with Fixed COM number and Hot-Swap.
- SUNIX DevicePort proprietary Ethernet I/O Redirection Technology.
- Supports Daisy Chain Topology and up to 255 COM ports expansion.
- Data buffer prevents any unforeseen data loss during a connection failure.
- Flexible port configuration with DevicePort on/off-line smart COM deployment.(Note 2)
- 15KV ESD protection for all serial signals meets IEC-61000-4-2 standard.
- Low power consumption design of 2.5W for meeting Green Environmental movement.
- Certified by CE, FCC, VCCI, BSMI, RoHS and Microsoft WHQL approval.
Introduction
DPAS04HP0 allows users to expand four RS-232 Powered COM ports over Ethernet connection, and it works on any windows based desktop, thin client, laptop, All-in-one, and tablet PC computers. With SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology, DevicePort® creates physical COM ports that support real time data communication, Smart COM on/off-line deployment, and Ethernet-COM port hot-plug capability; user can expand RS-232 COM port easily without complex software configuration. SUNIX DevicePort® improves solution deployment efficiency to achieve greater reliability in commercial and industrial automation applications.
Features
Specifications
Serial Communication
| Interface | RS-232 | Baud rate | 50bps ~115.2Kbps |
| Controller | SUNIX DPL2000Q | Stop bit | 1, 1.5, 2 |
| BUS | Ethernet | Parity | even, odd, none, mark, space |
| No. of Port | 2-port | Flow Control | Xon/Xoff (software) |
| FIFO | 1Kbyte Hardware / per port | Connector | DB9 Male |
| Signal | DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI | ||
| Protection |
±15KV ESD IEC-61000-4-2 Air Discharge ±8KV ESD IEC61000-4-2 Contact Discharge ±4KV ESD IEC61000-4-2 Level2 Line-to-Line |
||
Ethernet Communication
| Number of Ports | 4-port, Ethernet Switch Port |
| Speed | 10/100 Mbps, auto MDI/MDIX |
| Connector | RJ45 |
| Magnetic Isolation Protection | 1.0K Built-in |
Power Requirements
| Input Power Voltage | +5VDC |
| Output Powered COM Capacity |
+5VDC / Maximum 750mA / each port Note: Total power output capacity will be limited by connected power source. |
| Over Current Protection | 1.1A PTC fuse for each power signal |
| Power Consumption | 2.5W @ 5VDC (board only without power output to serial device) |
| Connector | DC-Jack |
Driver Support
| Windows Client | XP (X86) / 7 / 8 / 8.1 / 10 (X86/X64) |
| Windows Server | 2003 / 2008 / 2012R2 (X64) |
Regulatory Approvals
| Hardware | CE, FCC, VCCI, BSMI |
| Software |
Microsoft WHQL Windows • Microsoft Client: XP (X86) / 7 / 8 / 8.1 (X86/X64) • Microsoft Server: 2003/2008/2012R2 (X64) |
Environment
| Operation Temperature | 0 to 45°C (32 to 113°F) |
| Operation Humidity | 5 to 95% RH (non-condensing) |
| Storage Temperature | -20 to 85°C (-4 to 185°F) |
Physical Characteristics
| Housing | ABS, PC, Metal |
| Weight | 283g |
| Dimensions | 190x119.58x27(mm), 7.5x4.8x1.0(inch) |
Note:
1.DevicePort Advance Mode limits specific Ethernet port connection, and it does not works on router operation.
2.DevicePort on/off-line smart COM deployment.
- Auto connection and mapping with MAC address bound.
- Keeps physical COM port in system when DevicePort under off-line mode.
- Serial signal staging until DevicePort recovery back to on-line mode.
Accessories
Including Accessories
Power Adapter 5VDC@1A (US / EU)
- Partner No.: 1AAC-B205V10U10000 (US Type)
- Partner No.: 1AAC-B205V10E10000 (EU Type)
- US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
- (ψ5.5 *ψ2.0 / 120cm)
- Partner No.: 1WDC-Y1120G4100000
- 1 pcs
Support
Download Manual
| Manual | DevicePort Powered COM RS-232 Advanced Mode Manual |
|
| Version | V10 英文版 | |
| Update | 2016-05-25 09:51:13 | |
| Size | 4.3MB |
Download Datasheet
| Datasheet | DPAS04HP0 Datasheet |
|
Download Guide
| Guide | Advanced-Powered |
|
Download Driver
| Driver | DevicePortAdvanced V3.0.8.0 | |
| Version | Ver 3.0.8.0 | |
| Update | 2020-01-21 14:34:24 | |
| Size | 7.3MB | |
| OS |
Windows 10 32/64 bit
Windows 8.1 32/64 bit
Windows 8.0 32/64 bit
Windows 7 SP1 32/64 bit
Windows Server 2012 R2 64-bit
Windows Server 2012 64Bit
Windows Server 2008 R2 SP1 64bit
|
| Driver | Linux TTY Driver Ver 1.0.15.0 | |
| Version | Ver 1.0.15.0 | |
| Update | 2019-09-16 15:21:59 | |
| Size | 2MB | |
| OS |
CentOS7.0
Ubuntu 11.10
Ubuntu 12.04
Ubuntu 13.10
Ubuntu 14.04
Ubuntu 14.10
Ubuntu 15.04
Ubuntu 15.10
Ubuntu 16.04
|
DPAS04HP0 (phased out)
DevicePort Advanced Mode Powered COM Ethernet enabled 4-port RS-232 Port Replicator
- Expands 4 RS-232 serial ports over Ethernet or WiFi.
- Provides RS-232 serial ports with +5VDC power output via COM 9th pin.
- Communication speeds up to 115.2Kbps.
- Real-Time data transmitting (Real COM) without complicated IP setup.
- COM Port Auto-Detect and Port-Mapping supports Plug-N-Play.
- Built-in with SUNIX DPL2000Q High-Performance Ethernet-UART controller.
- Built-in dual 10/100 Ethernet ports for Ethernet cascading capability.
- Compatible with existing software and AP.
- To make wiring simple, fast, and more space efficient.
- Easy maintenance with Fixed COM number and Hot-Swap.
- SUNIX DevicePort proprietary Ethernet I/O Redirection Technology.
- Supports Daisy Chain Topology and up to 255 COM ports expansion.
- Data buffer prevents any unforeseen data loss during a connection failure.
- Flexible port configuration with DevicePort on/off-line smart COM deployment.(Note 2)
- 15KV ESD protection for all serial signals meets IEC-61000-4-2 standard.
- Low power consumption design of 2.5W for meeting Green Environmental movement.
- Certified by CE, FCC, VCCI, BSMI, RoHS and Microsoft WHQL approval.
DPAS04HP0 allows users to expand four RS-232 Powered COM ports over Ethernet connection, and it works on any windows based desktop, thin client, laptop, All-in-one, and tablet PC computers. With SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology, DevicePort® creates physical COM ports that support real time data communication, Smart COM on/off-line deployment, and Ethernet-COM port hot-plug capability; user can expand RS-232 COM port easily without complex software configuration. SUNIX DevicePort® improves solution deployment efficiency to achieve greater reliability in commercial and industrial automation applications.
Introduction
DPAS04HP0 allows users to expand four RS-232 Powered COM ports over Ethernet connection, and it works on any windows based desktop, thin client, laptop, All-in-one, and tablet PC computers. With SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology, DevicePort® creates physical COM ports that support real time data communication, Smart COM on/off-line deployment, and Ethernet-COM port hot-plug capability; user can expand RS-232 COM port easily without complex software configuration. SUNIX DevicePort® improves solution deployment efficiency to achieve greater reliability in commercial and industrial automation applications.
Features
Specifications
Serial Communication
| Interface | RS-232 | Baud rate | 50bps ~115.2Kbps |
| Controller | SUNIX DPL2000Q | Stop bit | 1, 1.5, 2 |
| BUS | Ethernet | Parity | even, odd, none, mark, space |
| No. of Port | 2-port | Flow Control | Xon/Xoff (software) |
| FIFO | 1Kbyte Hardware / per port | Connector | DB9 Male |
| Signal | DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI | ||
| Protection |
±15KV ESD IEC-61000-4-2 Air Discharge ±8KV ESD IEC61000-4-2 Contact Discharge ±4KV ESD IEC61000-4-2 Level2 Line-to-Line |
||
Ethernet Communication
| Number of Ports | 4-port, Ethernet Switch Port |
| Speed | 10/100 Mbps, auto MDI/MDIX |
| Connector | RJ45 |
| Magnetic Isolation Protection | 1.0K Built-in |
Power Requirements
| Input Power Voltage | +5VDC |
| Output Powered COM Capacity |
+5VDC / Maximum 750mA / each port Note: Total power output capacity will be limited by connected power source. |
| Over Current Protection | 1.1A PTC fuse for each power signal |
| Power Consumption | 2.5W @ 5VDC (board only without power output to serial device) |
| Connector | DC-Jack |
Driver Support
| Windows Client | XP (X86) / 7 / 8 / 8.1 / 10 (X86/X64) |
| Windows Server | 2003 / 2008 / 2012R2 (X64) |
Regulatory Approvals
| Hardware | CE, FCC, VCCI, BSMI |
| Software |
Microsoft WHQL Windows • Microsoft Client: XP (X86) / 7 / 8 / 8.1 (X86/X64) • Microsoft Server: 2003/2008/2012R2 (X64) |
Environment
| Operation Temperature | 0 to 45°C (32 to 113°F) |
| Operation Humidity | 5 to 95% RH (non-condensing) |
| Storage Temperature | -20 to 85°C (-4 to 185°F) |
Physical Characteristics
| Housing | ABS, PC, Metal |
| Weight | 283g |
| Dimensions | 190x119.58x27(mm), 7.5x4.8x1.0(inch) |
Note:
1.DevicePort Advance Mode limits specific Ethernet port connection, and it does not works on router operation.
2.DevicePort on/off-line smart COM deployment.
- Auto connection and mapping with MAC address bound.
- Keeps physical COM port in system when DevicePort under off-line mode.
- Serial signal staging until DevicePort recovery back to on-line mode.
Accessories
Including Accessories
Power Adapter 5VDC@1A (US / EU)
- Partner No.: 1AAC-B205V10U10000 (US Type)
- Partner No.: 1AAC-B205V10E10000 (EU Type)
- US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
- (ψ5.5 *ψ2.0 / 120cm)
- Partner No.: 1WDC-Y1120G4100000
- 1 pcs
Support
Download Manual
| Manual | DevicePort Powered COM RS-232 Advanced Mode Manual |
|
| Version | V10 英文版 | |
| Update | 2016-05-25 09:51:13 | |
| Size | 4.3MB |
Download Datasheet
| Datasheet | DPAS04HP0 Datasheet |
|
Download Guide
| Guide | Advanced-Powered |
|
Download Driver
| Driver | DevicePortAdvanced V3.0.8.0 | |
| Version | Ver 3.0.8.0 | |
| Update | 2020-01-21 14:34:24 | |
| Size | 7.3MB | |
| OS |
Windows 10 32/64 bit
Windows 8.1 32/64 bit
Windows 8.0 32/64 bit
Windows 7 SP1 32/64 bit
Windows Server 2012 R2 64-bit
Windows Server 2012 64Bit
Windows Server 2008 R2 SP1 64bit
|
| Driver | Linux TTY Driver Ver 1.0.15.0 | |
| Version | Ver 1.0.15.0 | |
| Update | 2019-09-16 15:21:59 | |
| Size | 2MB | |
| OS |
CentOS7.0
Ubuntu 11.10
Ubuntu 12.04
Ubuntu 13.10
Ubuntu 14.04
Ubuntu 14.10
Ubuntu 15.04
Ubuntu 15.10
Ubuntu 16.04
|
