iDP200D00

iDevicePort Ethernet Based I/O Hub 2-port RS-232
  • Extend dual RS-232 serial port over Local Area Network.
  • Built-in SUNIX DevicePort DPL2000Q High-Performance Ethernet-UART controller.
  • ESD protection for all serial signal lines meeting IEC-61000-4-2 standard.
  • Provide a complete SDK for iOS & Android software developers.
  • Support for iOS & Android operating systems.

Introduction

SUNIX iDevicePort® series is designed for Mobile devices, allowing users to expand traditional I/O connectives on Mobile devices over a Local Area Network. It built-in SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology. SUNIX iDevicePort® creates remoted COM channel that supports real time data communication, device sharing, Smart COM on/off-line deployment features. With SUNIX API (Application Programming Interface) and SDK (software development kit), software application designer can easily control and access I/O port without complicated programming under Mobile operation system.
 
SUNIX IDP200D00 is a network-attached dual channel RS-232 COM hub that connects traditional serial peripheral devices to a mobile device over a Local Area Network. By connecting to standard Wi-Fi router, iOS & Android devices can access remoted RS-232 devices wirelessly. It’s the best and creative solution for commercial automation and retail POS applications.

Features

Connect your POS Accessory to iOS Device
SUNIX iDP extends Serial and USB connectivity over Ethernet Networking on iOS.
Supports current POS Accessory (Printer, Cash Drawer, Scanner) 

Connect your POS Accessory to iOS Device

iDP Device Sharing
   ˙ Enable iDP's connected peripheral to be shared.
   ˙ Share Serial/USB devices between multiple hosts.
   ˙ Support SDK for further customized design.

iDP Device Sharing

Specifications

Serial Communication

Interface RS-232 Baud rate 50bps ~115.2Kbps
Controller SUNIX DPL2000Q Stop bit 1, 1.5, 2
BUS Ethernet Parity even, odd, none, mark, space
No. of Port 2-port Flow Control Xon/Xoff (software)
FIFO 1Kbyte Hardware / per port Connector DB9 Male
Signal DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI

Ethernet Communication

Number of Ports 1-port, Ethernet Switch Port
Speed 10/100 Mbps, auto MDI/MDIX
Connector RJ45
Magnetic Isolation Protection 1.0K Built-in

Power Requirements

Input Power Voltage 5 VDC
Power Consumption 2.5W @ 5VDC
Connector DC-Jack

Driver Support

iOS 8.x or later
Android 4.x or later

Environment

Operation Temperature 0 to 60°C (32 to 140°F)
Operation Humidity 5 to 95% RH  (non-condensing)
Storage Temperature -20 to 85°C (-4 to 185°F)

Physical Characteristics

Housing ABS, PC, Metal
Weight 145 g
Dimensions 121x81.93x27(mm), 4.7x3.2x1.0(inch)

Accessories

Including Accessories

Power Adapter 5VDC@1A (US / EU)
  • Partner No.: 1AAC-B205V10U10000 (US Type)
  • Partner No.: 1AAC-B205V10E10000 (EU Type)
  • US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
  • (ψ5.5 *ψ2.0 / 120cm)
  • Partner No.: 1WDC-Y1120G4100000
  • 1 pcs

Support

Download Manual

Manual iDevicePort Quick Installation Guide - 771IDPQIG000-S04

Download Datasheet

Datasheet IDP200D00 Datasheet

Download Driver

Driver aDP_SDK_v1.3.1
Version Ver 1.3.1
Update 2019-06-12 16:54:56
Size 26MB
OS
Android 4.x above
Driver aDP_SDK_v1.3
Version Ver 1.3
Update 2018-04-17 17:36:46
Size 36.6MB
OS
Android 4.x above
Driver iDP_SDK_v3.8
Version Ver 3.8
Update 2020-04-01 16:14:04
Size 115.5MB
OS
iOS 8.x above
Driver iDP_SDK_v3.6
Version Ver 3.6
Update 2019-12-31 09:30:49
Size 101.3MB
OS
iOS 8.x above
Firmware IDP200D00_MT0_V1_1
Version Ver 1.1
Update 2017-12-14 18:44:36
Size 3.9MB
OS NULL

iDP200D00

iDevicePort Ethernet Based I/O Hub 2-port RS-232
  • Extend dual RS-232 serial port over Local Area Network.
  • Built-in SUNIX DevicePort DPL2000Q High-Performance Ethernet-UART controller.
  • ESD protection for all serial signal lines meeting IEC-61000-4-2 standard.
  • Provide a complete SDK for iOS & Android software developers.
  • Support for iOS & Android operating systems.

Introduction

SUNIX iDevicePort® series is designed for Mobile devices, allowing users to expand traditional I/O connectives on Mobile devices over a Local Area Network. It built-in SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology. SUNIX iDevicePort® creates remoted COM channel that supports real time data communication, device sharing, Smart COM on/off-line deployment features. With SUNIX API (Application Programming Interface) and SDK (software development kit), software application designer can easily control and access I/O port without complicated programming under Mobile operation system.
 
SUNIX IDP200D00 is a network-attached dual channel RS-232 COM hub that connects traditional serial peripheral devices to a mobile device over a Local Area Network. By connecting to standard Wi-Fi router, iOS & Android devices can access remoted RS-232 devices wirelessly. It’s the best and creative solution for commercial automation and retail POS applications.

Features

Connect your POS Accessory to iOS Device
SUNIX iDP extends Serial and USB connectivity over Ethernet Networking on iOS.
Supports current POS Accessory (Printer, Cash Drawer, Scanner) 

Connect your POS Accessory to iOS Device

iDP Device Sharing
   ˙ Enable iDP's connected peripheral to be shared.
   ˙ Share Serial/USB devices between multiple hosts.
   ˙ Support SDK for further customized design.

iDP Device Sharing

Specifications

Serial Communication

Interface RS-232 Baud rate 50bps ~115.2Kbps
Controller SUNIX DPL2000Q Stop bit 1, 1.5, 2
BUS Ethernet Parity even, odd, none, mark, space
No. of Port 2-port Flow Control Xon/Xoff (software)
FIFO 1Kbyte Hardware / per port Connector DB9 Male
Signal DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI

Ethernet Communication

Number of Ports 1-port, Ethernet Switch Port
Speed 10/100 Mbps, auto MDI/MDIX
Connector RJ45
Magnetic Isolation Protection 1.0K Built-in

Power Requirements

Input Power Voltage 5 VDC
Power Consumption 2.5W @ 5VDC
Connector DC-Jack

Driver Support

iOS 8.x or later
Android 4.x or later

Environment

Operation Temperature 0 to 60°C (32 to 140°F)
Operation Humidity 5 to 95% RH  (non-condensing)
Storage Temperature -20 to 85°C (-4 to 185°F)

Physical Characteristics

Housing ABS, PC, Metal
Weight 145 g
Dimensions 121x81.93x27(mm), 4.7x3.2x1.0(inch)

Accessories

Including Accessories

Power Adapter 5VDC@1A (US / EU)
  • Partner No.: 1AAC-B205V10U10000 (US Type)
  • Partner No.: 1AAC-B205V10E10000 (EU Type)
  • US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
  • (ψ5.5 *ψ2.0 / 120cm)
  • Partner No.: 1WDC-Y1120G4100000
  • 1 pcs

Support

Download Manual

Manual iDevicePort Quick Installation Guide - 771IDPQIG000-S04

Download Datasheet

Datasheet IDP200D00 Datasheet

Download Driver

Driver aDP_SDK_v1.3.1
Version Ver 1.3.1
Update 2019-06-12 16:54:56
Size 26MB
OS
Android 4.x above
Driver aDP_SDK_v1.3
Version Ver 1.3
Update 2018-04-17 17:36:46
Size 36.6MB
OS
Android 4.x above
Driver iDP_SDK_v3.8
Version Ver 3.8
Update 2020-04-01 16:14:04
Size 115.5MB
OS
iOS 8.x above
Driver iDP_SDK_v3.6
Version Ver 3.6
Update 2019-12-31 09:30:49
Size 101.3MB
OS
iOS 8.x above
Firmware IDP200D00_MT0_V1_1
Version Ver 1.1
Update 2017-12-14 18:44:36
Size 3.9MB
OS NULL

iDP200D00

iDevicePort Ethernet Based I/O Hub 2-port RS-232
  • Extend dual RS-232 serial port over Local Area Network.
  • Built-in SUNIX DevicePort DPL2000Q High-Performance Ethernet-UART controller.
  • ESD protection for all serial signal lines meeting IEC-61000-4-2 standard.
  • Provide a complete SDK for iOS & Android software developers.
  • Support for iOS & Android operating systems.

Introduction

SUNIX iDevicePort® series is designed for Mobile devices, allowing users to expand traditional I/O connectives on Mobile devices over a Local Area Network. It built-in SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology. SUNIX iDevicePort® creates remoted COM channel that supports real time data communication, device sharing, Smart COM on/off-line deployment features. With SUNIX API (Application Programming Interface) and SDK (software development kit), software application designer can easily control and access I/O port without complicated programming under Mobile operation system.
 
SUNIX IDP200D00 is a network-attached dual channel RS-232 COM hub that connects traditional serial peripheral devices to a mobile device over a Local Area Network. By connecting to standard Wi-Fi router, iOS & Android devices can access remoted RS-232 devices wirelessly. It’s the best and creative solution for commercial automation and retail POS applications.

Features

Connect your POS Accessory to iOS Device
SUNIX iDP extends Serial and USB connectivity over Ethernet Networking on iOS.
Supports current POS Accessory (Printer, Cash Drawer, Scanner) 

Connect your POS Accessory to iOS Device

iDP Device Sharing
   ˙ Enable iDP's connected peripheral to be shared.
   ˙ Share Serial/USB devices between multiple hosts.
   ˙ Support SDK for further customized design.

iDP Device Sharing

Specifications

Serial Communication

Interface RS-232 Baud rate 50bps ~115.2Kbps
Controller SUNIX DPL2000Q Stop bit 1, 1.5, 2
BUS Ethernet Parity even, odd, none, mark, space
No. of Port 2-port Flow Control Xon/Xoff (software)
FIFO 1Kbyte Hardware / per port Connector DB9 Male
Signal DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI

Ethernet Communication

Number of Ports 1-port, Ethernet Switch Port
Speed 10/100 Mbps, auto MDI/MDIX
Connector RJ45
Magnetic Isolation Protection 1.0K Built-in

Power Requirements

Input Power Voltage 5 VDC
Power Consumption 2.5W @ 5VDC
Connector DC-Jack

Driver Support

iOS 8.x or later
Android 4.x or later

Environment

Operation Temperature 0 to 60°C (32 to 140°F)
Operation Humidity 5 to 95% RH  (non-condensing)
Storage Temperature -20 to 85°C (-4 to 185°F)

Physical Characteristics

Housing ABS, PC, Metal
Weight 145 g
Dimensions 121x81.93x27(mm), 4.7x3.2x1.0(inch)

Accessories

Including Accessories

Power Adapter 5VDC@1A (US / EU)
  • Partner No.: 1AAC-B205V10U10000 (US Type)
  • Partner No.: 1AAC-B205V10E10000 (EU Type)
  • US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
  • (ψ5.5 *ψ2.0 / 120cm)
  • Partner No.: 1WDC-Y1120G4100000
  • 1 pcs

Support

Download Manual

Manual iDevicePort Quick Installation Guide - 771IDPQIG000-S04

Download Datasheet

Datasheet IDP200D00 Datasheet

Download Driver

Driver aDP_SDK_v1.3.1
Version Ver 1.3.1
Update 2019-06-12 16:54:56
Size 26MB
OS
Android 4.x above
Driver aDP_SDK_v1.3
Version Ver 1.3
Update 2018-04-17 17:36:46
Size 36.6MB
OS
Android 4.x above
Driver iDP_SDK_v3.8
Version Ver 3.8
Update 2020-04-01 16:14:04
Size 115.5MB
OS
iOS 8.x above
Driver iDP_SDK_v3.6
Version Ver 3.6
Update 2019-12-31 09:30:49
Size 101.3MB
OS
iOS 8.x above
Firmware IDP200D00_MT0_V1_1
Version Ver 1.1
Update 2017-12-14 18:44:36
Size 3.9MB
OS NULL

iDP200D00

iDevicePort Ethernet Based I/O Hub 2-port RS-232
  • Extend dual RS-232 serial port over Local Area Network.
  • Built-in SUNIX DevicePort DPL2000Q High-Performance Ethernet-UART controller.
  • ESD protection for all serial signal lines meeting IEC-61000-4-2 standard.
  • Provide a complete SDK for iOS & Android software developers.
  • Support for iOS & Android operating systems.
SUNIX iDevicePort® series is designed for Mobile devices, allowing users to expand traditional I/O connectives on Mobile devices over a Local Area Network. It built-in SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology. SUNIX iDevicePort® creates remoted COM channel that supports real time data communication, device sharing, Smart COM on/off-line deployment features. With SUNIX API (Application Programming Interface) and SDK (software development kit), software application designer can easily control and access I/O port without complicated programming under Mobile operation system.
 
SUNIX IDP200D00 is a network-attached dual channel RS-232 COM hub that connects traditional serial peripheral devices to a mobile device over a Local Area Network. By connecting to standard Wi-Fi router, iOS & Android devices can access remoted RS-232 devices wirelessly. It’s the best and creative solution for commercial automation and retail POS applications.

Introduction

SUNIX iDevicePort® series is designed for Mobile devices, allowing users to expand traditional I/O connectives on Mobile devices over a Local Area Network. It built-in SUNIX DPL2000Q High-Performance Ethernet-UART controller and exclusive I/O Redirection Technology. SUNIX iDevicePort® creates remoted COM channel that supports real time data communication, device sharing, Smart COM on/off-line deployment features. With SUNIX API (Application Programming Interface) and SDK (software development kit), software application designer can easily control and access I/O port without complicated programming under Mobile operation system.
 
SUNIX IDP200D00 is a network-attached dual channel RS-232 COM hub that connects traditional serial peripheral devices to a mobile device over a Local Area Network. By connecting to standard Wi-Fi router, iOS & Android devices can access remoted RS-232 devices wirelessly. It’s the best and creative solution for commercial automation and retail POS applications.

Features

Connect your POS Accessory to iOS Device
SUNIX iDP extends Serial and USB connectivity over Ethernet Networking on iOS.
Supports current POS Accessory (Printer, Cash Drawer, Scanner) 

Connect your POS Accessory to iOS Device

iDP Device Sharing
   ˙ Enable iDP's connected peripheral to be shared.
   ˙ Share Serial/USB devices between multiple hosts.
   ˙ Support SDK for further customized design.

iDP Device Sharing

Specifications

Serial Communication

Interface RS-232 Baud rate 50bps ~115.2Kbps
Controller SUNIX DPL2000Q Stop bit 1, 1.5, 2
BUS Ethernet Parity even, odd, none, mark, space
No. of Port 2-port Flow Control Xon/Xoff (software)
FIFO 1Kbyte Hardware / per port Connector DB9 Male
Signal DCD, TxD, RxD, RTS, CTS, DTR, DSR, GND, RI

Ethernet Communication

Number of Ports 1-port, Ethernet Switch Port
Speed 10/100 Mbps, auto MDI/MDIX
Connector RJ45
Magnetic Isolation Protection 1.0K Built-in

Power Requirements

Input Power Voltage 5 VDC
Power Consumption 2.5W @ 5VDC
Connector DC-Jack

Driver Support

iOS 8.x or later
Android 4.x or later

Environment

Operation Temperature 0 to 60°C (32 to 140°F)
Operation Humidity 5 to 95% RH  (non-condensing)
Storage Temperature -20 to 85°C (-4 to 185°F)

Physical Characteristics

Housing ABS, PC, Metal
Weight 145 g
Dimensions 121x81.93x27(mm), 4.7x3.2x1.0(inch)

Accessories

Including Accessories

Power Adapter 5VDC@1A (US / EU)
  • Partner No.: 1AAC-B205V10U10000 (US Type)
  • Partner No.: 1AAC-B205V10E10000 (EU Type)
  • US Type or EU Type x 1 pcs
Power Jack to USB TyepA Male Cable
  • (ψ5.5 *ψ2.0 / 120cm)
  • Partner No.: 1WDC-Y1120G4100000
  • 1 pcs

Support

Download Manual

Manual iDevicePort Quick Installation Guide - 771IDPQIG000-S04

Download Datasheet

Datasheet IDP200D00 Datasheet

Download Driver

Driver aDP_SDK_v1.3.1
Version Ver 1.3.1
Update 2019-06-12 16:54:56
Size 26MB
OS
Android 4.x above
Driver aDP_SDK_v1.3
Version Ver 1.3
Update 2018-04-17 17:36:46
Size 36.6MB
OS
Android 4.x above
Driver iDP_SDK_v3.8
Version Ver 3.8
Update 2020-04-01 16:14:04
Size 115.5MB
OS
iOS 8.x above
Driver iDP_SDK_v3.6
Version Ver 3.6
Update 2019-12-31 09:30:49
Size 101.3MB
OS
iOS 8.x above
Firmware IDP200D00_MT0_V1_1
Version Ver 1.1
Update 2017-12-14 18:44:36
Size 3.9MB
OS NULL